Pure Boost, Garment Steamer, 2-in-1 Steaming and Ironing

• Untreated tap water:
Your appliance has been designed to use untreated tap water.
If your water is very hard, mix 50% untreated tap water and 50% distilled water.

• Types of water not to use:
Heat concentrates the elements contained in water during evaporation. The types of water listed below may contain organic waste, mineral or chemical elements that can cause spitting, brown staining or premature wear of the appliance:
- water from clothes dryers
- scented or softened water
- water from refrigerators, batteries, air conditioners
- rain water
- boiled, filtered or bottled water

In order to ensure the best performance from your iron, these types of water should not be used for ironing.

The 2‑in‑1 PureForce steamer lets you steam vertically and iron horizontally. It heats up quickly (25 seconds) and produces a high amount of steam to remove creases effectively. Its tank is removable. The steam removes unpleasant odours. It offers 4 steam settings suitable for all fabrics and uses less energy in Eco mode. Ergonomic, it is easy to use on a daily basis.

The main difference between the PureForce steamer and a regular steamer is that the PureForce is a 2‑in‑1 appliance: it allows you to steam vertically and iron horizontally, whereas a regular steamer only steams vertically.

The PureForce steamer is designed to be used on all ironable fabrics. It offers 4 steam settings and a Boost mode, allowing use adapted to each textile, from the most delicate to the most robust. In addition, it comes with two reversible pads: *a lint‑removal/velvet pad and *a microfibre/velvet pad, for complete care of your garments.

Please always check the care label on your garment or textile before using the steamer. First test on a less visible area to ensure the appliance is suitable for your fabric.

*Depending on model

Before any handling, unplug the appliance and let it cool down for at least one hour. Once completely cold, you can install or remove the pad by gently clipping or unclipping it, depending on the model. Make sure the pad is securely attached before switching the appliance back on.
Never handle the pad when the appliance is hot or in use.

Depending on the model, your steamer may come with one reversible pad or two separate pads:

Velvet side (black): used during steaming to glide easily over the fabric without damaging it.

Anti‑hair / anti‑lint side (grey): removes hair, lint and bobbles from the surface of the fabric.

Microfibre side (white): captures fine particles inside the fabrics for light cleaning.

To fill the tank, gently remove it. Open the filling cap, fill it with untreated tap water up to the MAX level, then close the cap. Put the tank back in place until it clicks into position.

This appliance is designed to work with regular tap water. Do not use pure distilled or demineralised water. If your water is very hard (over 30 °F, 17°dH or 21°e), mix 50% tap water with 50% commercially available demineralised water. Never use water containing additives (starch, perfume, aromatic substances, softener, etc.), or condensed water (for example water from tumble dryers, refrigerators or air conditioners, or rainwater). This type of water contains organic waste and minerals that become concentrated under the effect of heat and can cause spitting, brown stains or premature wear of your appliance.

The appliance heats up in about 25 seconds; an indicator light and a sound signal show that it is ready for use.

Plug in the appliance and switch it on by pressing the On/Off button. Wait until the indicator stops flashing; a beep will let you know the appliance is ready to use. To switch the appliance off, press and hold the On/Off button. Then unplug the appliance.

Yes, this noise is related to the time needed for the pump to prime.

To produce steam, press the steam trigger.

Yes, this is due to the movement of water inside the product.

Yes, the appliance can be used horizontally. PureForce is designed as a 2‑in‑1 product, allowing you to steam vertically and iron horizontally.

The steam output is reduced in the horizontal position to prevent drops of water that have not turned into steam from wetting your clothes.

For optimal vertical use, direct the steam jets towards your garment with up‑and‑down movements, keeping the steam head in contact with the fabric.

For horizontal use, move the steamer back and forth on the ironing board, keeping the steam head in contact with the fabric. Be careful of the burst of steam when you tilt the product from horizontal to vertical.

To activate BOOST mode, press the SELECT button for 2 seconds until the BOOST indicator flashes.
Press the steam trigger while holding the steamer facing the garment in a vertical position.

To deactivate BOOST mode, press SELECT again until the light returns to the previously used mode.

To obtain a continuous flow of steam, quickly press the trigger twice. To stop it, press the trigger once again.

No, you must never use the appliance directly on yourself or on another person. The steam is very hot and can cause burns.

The appliance is equipped with an automatic shut‑off system that activates after about 8 minutes of inactivity.

After unplugging the appliance, remove the water tank and open the filling cap. Empty the tank completely, then close the cap and put the tank back in place.
Let the appliance cool down for at least one hour before storing it.
Wrap the cord around itself and secure it with the hook‑and‑loop strap. Clean the appliance with a soft or microfibre cloth.
Finally, store the appliance in a clean, dry place away from moisture and heat, such as a cupboard.

The PureForce DR87 steamer offers 4 steam modes and 1 Boost mode:
- Boost
- Very High
- High
- Medium
- Eco

 

After unplugging the appliance, wait one hour for it to cool down completely. Use only a soft sponge with water to clean the appliance. Never wash or rinse the appliance directly over a sink. The reversible pad can be hand‑washed with clean water and soap. Wait until it is dry before using it again.

No, you must not use any detergents to clean the appliance.

Yes, the appliance needs descaling.

To do this, follow these steps:

Perform this operation in a well‑ventilated room.
Remove the water tank.
Fill the water tank with 50% water and 50% white vinegar. Do not use any other descaling products.
Put the tank back in place until it clicks.

Plug in the appliance.
Switch on the appliance.
Wait until the indicator stops flashing through the different modes (about 25 seconds). When the light is steady, the appliance is ready to use.
Run the appliance until the water tank is completely empty. Do this operation in vertical use only.
Press and hold the On/Off button to switch off the appliance.

Unplug the appliance and remove the tank.
Open the water tank cap, rinse the tank and fill it with tap water.
Put the water tank back in place in the appliance. Make sure the water tank is correctly positioned.

Plug in the appliance.
Switch on the appliance.
Wait until the indicator stops flashing through the different modes (about 25 seconds). A beep indicates that your appliance is ready to use.
Run the appliance until the water tank is completely empty. Do this operation in vertical use only.

Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I".
The water level in the tank is too low ==> Unplug the appliance and fill the tank.
The pump is unprimed ==>Press and hold the steam button for a few seconds to prime the pump.
The removable tank is not installed correctly ==> Check the correct positioning of the tank on the product.
The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.

Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I".
The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.

The water tank is not installed correctly or its locking valve is not closed properly ==> Check that the valve is closed and that the tank is installed correctly on the product.

Your appliance has limescale, consult the "Descaling" section in the instructions.

The "Steam" button is in Continuous Steam position. Unlock it by pressing it once.

You have used descaling chemicals or additives in the water.
Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.

You have used descaling chemicals or additives in the water.
Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.

Do not use your appliance. To avoid any danger, have it replaced by an approved repair centre.

If your product is not producing steam, check the following points:

The product is not plugged in or switched on
→ Make sure it is correctly connected to a power outlet, switch the appliance on and wait until the indicator stops flashing; a beep will let you know the appliance is ready to use.

The water level is too low
→ Unplug the appliance and fill the water tank.

The pump has lost its prime
→ Hold down the steam button for a few seconds to re‑prime the pump.

You are not pressing the steam button.
→ Press the steam button to produce steam.

The removable tank is not correctly fitted
→ Check that it is properly clicked into place on the appliance.

If your product no longer heats up, check the following points:

Check that the appliance is properly plugged in and switched on.
→ Make sure it is correctly connected to a power outlet, switch the appliance on and wait until the indicator stops flashing; a beep will let you know the appliance is ready to use.

The product may be in “Auto‑OFF” mode.
→ Press the On/Off button and wait until the light stops flashing.

The water tank is not correctly installed or its cap is not properly closed.

Take your device to a recycling center or waste disposal facility.

If you believe a part is missing, please contact our customer service center and we will help you find an appropriate solution.

Please go to the “Accessories” section of the website to easily find whatever you need for your product.

Find more detailed information in the Warranty section of the website.

Take your appliance to a recycling centre or a waste disposal facility.

If you think a part is missing, contact the consumer services centre and we will help you find an appropriate solution.

You can find accessories, consumables and spare parts for your product by visiting the accessories shop on the website.

All information is detailed in the Warranty section of this website.